您好,欢迎访问无锡乐夫门栏设计.安装.生产厂家!

无锡铝艺大门

厂家直销更实惠

无锡铝艺护栏

品质值得您信赖

全国厂家施工咨询电话

135-1526-9028

无锡乐夫门栏设计.安装.生产厂家

在无锡铝艺大门喷漆时需要哪些操作流程呢?

发布时间:2019-06-12人气:984
在无锡地区铝艺庭院大门选购绝招及考虑细节在无锡铝艺大门喷漆时需要哪些操作流程呢?随着无锡居民生活水平的提高,人们的防盗意识也有所增强,采取的防盗措施也变得多种多样。在无锡居民生活中总… 无锡铝艺护栏焊接加工注重的四个技术条件在无锡铝艺大门喷漆时需要哪些操作流程呢?铝艺护栏成长距今已有5个年初了,在这几年人们也目击了无锡铝艺围栏的前进和腾飞:在表面上愈来愈美观,在工…

现如今,大多数无锡人在安装大门时都会选择无锡铝艺大门,尤其是有些别墅大门也都安装的铝艺大门,其实对于铝艺大门安装装修时喷漆是一个比较重要的过程,铝艺大门的美观度全靠喷漆来装饰效果,为了保证喷漆效果不仅要选好油漆,而且对喷漆的方法也有很高的要求。那么在无锡铝艺大门喷漆时需要哪些操作流程呢?下面就一起来看看吧。铝艺大门喷漆流程:

Nowadays, most people choose aluminium art doors when installing doors, especially some villas. In fact, painting is an important process when installing and decorating aluminium art doors. The beauty of aluminium art doors depends entirely on the decorative effect of spraying paint. In order to ensure the effect of spraying paint, it is necessary not only to select good paint, but also to spray paint methods. Ask. So what kind of operation process is needed when spraying paint on Jinan aluminium art gate? Let's take a look at it. Spraying process for aluminium door:

1、打磨:找一个长方体,以手能握住为宜。将其中一比较平整的一面,用砂纸裹住,手压住后打磨。打磨平面的方向顺序是:先横后竖。打磨时,要先上后下,先外后里,砂纸的选用是先粗后细。铝艺大门的转角和造型以及细节部位,就得用手了。为什么要打磨呢?一方面是为了去掉原油漆和漆面上的杂质,另一方面是为了增加新油漆的附着力。

1. Grinding: Find a cuboid that you can hold with your hand. One of the more flat side, wrapped in sandpaper, hand pressed and polished. The direction order of polishing plane is: first horizontal and then vertical. When polishing, first up and then down, first outside and then inside, the choice of sandpaper is first thick and then fine. The corner, shape and details of the aluminium door have to be handled. Why do you want to polish? On the one hand, it is to remove impurities from crude oil paint and paint surface, on the other hand, it is to increase the adhesion of new paint.

2、刷漆前的准备:打磨完毕后,看铝艺大门是否有凹凸不平的地方,若有,用腻子找平,再次打磨至平整状态。然后将艺大门周围及地板做保护,防止油漆污染这些地方。并用水份很小的湿毛巾擦拭铝艺大门。将桶装油漆用小棍搅拌均匀,手的运动速度不要太快,防止溅出。

2. Preparations before painting: After polishing, see if there are any uneven areas in the aluminium art gate. If so, leveling with putty and polishing again to a flat state. Then protect the area around the art gate and the floor to prevent the paint from polluting these areas. Wipe the door with a wet towel with very little moisture. Stir the barreled paint evenly with a stick. Don't move your hands too fast to prevent splashing.

3、进行刷漆:在刷第一次木器漆的时候,调底漆是一项非常重要的工序,调底漆还要知道木器的密度,那些比较硬的木器密度高,底漆就可以调得稀一点,而软的木器底漆就要调得粘稠一点。在开始刷漆的时候,要顺着木器的纹路涂刷均匀,不要涂得太厚了,等木器漆完全干透后用砂纸打磨,打磨到你摸上去感觉到光滑,没有突起就可以了,然后再用软湿布擦拭几次,最后擦干。而使用刷涂可以使木蜡油的渗透深度更大,也使施工的速度加快。刷第二次漆就要调得稀一点了,刷完之后能盖住第一次刷的木器漆,然后用500目以上的水砂纸跟着刷漆的方向打磨,打磨要打磨得均匀。使用擦涂可以节省木器漆的用量。等到第二次漆或者最后一次漆表干之后,要立刻用干净的棉布擦拭木器表面,使得木器表面变得光滑。刷完第三次漆,要用更细得水砂纸打磨,要蘸水打磨,打磨的力度要均匀,不宜过重也不宜过轻。上了最后一次漆之后是不需要打磨的,你可以上一层铝艺大门保护蜡。添加擦涂的次数,并且每一次涂完都用细砂纸打磨,最后一次用薄擦和表干后擦拭可以获得高档铝艺大门的效果。

3. Painting: In brushing the first wood primer, adjusting the primer is a very important process, adjusting the primer also need to know the density of wood, those harder wood density, primer can be adjusted a little thinner, and soft wood primer should be adjusted a little more sticky. When you start painting, you should brush along the lines of the woodwork evenly. Don't paint too thick. When the woodwork paint is completely dry, sandpaper is used to polish it until you feel smooth and there is no protuberance. Then wipe it several times with a soft wet cloth, and finally dry it. Brushing can make the penetration depth of paraffin oil deeper and speed up the construction. Brush the second paint to be thinner, after brushing can cover the first brush of wood paint, and then use more than 500 mesh sandpaper to follow the direction of the paint polishing, polishing to be uniform. The use of brushing can save the amount of wood paint. When the second paint or the last paint is dry, wipe the wood surface with clean cotton cloth immediately to make the wood surface smooth. Finish the third paint, to use more fine water sandpaper grinding, to dip in water grinding, grinding force to be even, not too heavy and not too light. You don't need to polish after the last paint. You can put on a protective wax for the aluminium door. Add the number of times of rubbing, and every time the finish of rubbing with fine sandpaper, the last time with thin rubbing and surface drying can be wiped to obtain the effect of high-grade aluminum door.

4、漆层保护:通常铝艺大门在涂刷完毕后,要涂刷清漆,对油漆层进行保护和增亮。清漆也和油漆涂刷方法一致,不过每次油漆刷所沾漆量较少,摊开清漆所挥动手腕的次数也再多。清漆建议最少两遍,若有毛刷掉毛现象,一定要及时处理所掉的毛,注意清漆只刷铝艺大门表面不刷里面。

4. Lacquer protection: Aluminum doors are usually painted with varnish to protect and brighten the paint layer after finishing painting. The varnish is also the same as the paint brushing method, but each time the amount of varnish brush is less, the number of times the varnish is spread and the wrist is waved is more. Varnish is recommended at least twice, if there is a phenomenon of hair brushing off, we must deal with the hair in time, pay attention to varnish only brush the surface of the aluminium art door without brushing inside. 

在无锡地区铝艺大门的价格受哪些因素影响?无锡铝艺大门 铝艺大门的价格受哪些因素影响?现在越来越多的家庭装修都开始选择无锡铝艺大门了,因为相比较实庭院门来说,价格要实惠的多,而跟铝合金门相比,更加美观实用,因此铝艺大门综合来说性价比比较高,那么铝艺大门的价格是多少呢?又受那些因素所影响呢?下面就针对这些问题为大家详细介绍一下。铝艺护栏价格,铝艺配… 在无锡购买别墅铝艺大门选购可以从哪些地方考虑呢?无锡铝艺大门 什么是别墅铝艺大门?在无锡购买别墅铝艺大门选购可以从哪些地方考虑呢?无锡别墅铝艺大门在性能上要优于推拉窗,但推拉窗在加工制作与操作使用上要优于别墅铝艺大门。正因为这方面的原因,别墅铝艺大门大量的应用于城市的商住楼、写字楼、高档住宅、别墅等中高档建筑,而推拉窗则广泛的用于工业厂房、乡村住宅等中…
辛苦整理!转载请注明来自 http://yxchgs.com/news/xw2/116.html

推荐资讯